Product Core Brief
- Model: 330130-045-01-00
- Brand: Bently Nevada (Baker Hughes)
- Series: 3300 XL 8 mm Proximity Transducer System
- Core Function: Armored extension cable that connects a 3300 XL 8 mm proximity probe to a 3300 XL Proximitor sensor.
- Product Type: 3300 XL 8 mm armored extension cable
- Key Specs: 4.5 m cable length | Armored | No agency approval | ClickLoc connector | Compatible with 3300 XL 8 mm probes and Proximitor sensors
- Condition: New Surplus / Factory New (confirm label, cable jacket condition, and connector integrity before procurement)
Product Introduction
The Bently Nevada 330130-045-01-00 is a 3300 XL 8 mm armored extension cable used to connect a 3300 XL 8 mm proximity probe to a 3300 XL Proximitor sensor. It is part of the 3300 XL eddy-current transducer system, which measures shaft relative vibration, axial displacement, eccentricity, and keyphasor reference on rotating machinery.
The model code breaks down as follows:
| Segment | Value | Meaning |
|---|---|---|
| Base model | 330130 | 3300 XL extension cable |
| Length | 045 | 4.5 m cable length |
| Armor / temperature | 01 | Armored cable |
| Approval | 00 | No agency approval |
The 330130 series extension cable uses ClickLoc connectors to maintain signal integrity between the probe and the Proximitor sensor. The 3300 XL system is designed for full interchangeability, meaning individual components do not require matched calibration when replaced with the same series and size.
The armored construction provides additional mechanical protection for the cable during routing through conduit, cable trays, or areas where the cable may be exposed to abrasion or impact. This makes it suitable for harsh industrial environments.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Product Type | 3300 XL 8 mm armored extension cable |
| Brand | Bently Nevada (Baker Hughes) |
| Model | 330130-045-01-00 |
| Cable Length | 4.5 m (14.8 ft) |
| Armor | Armored |
| Temperature Rating | Standard temperature range |
| Connector Type | ClickLoc |
| Approval | 00 (No agency approval) |
| System Compatibility | 3300 XL 8 mm proximity probe + 3300 XL Proximitor sensor |
| Typical Applications | Shaft vibration, axial displacement, keyphasor, eccentricity, speed measurement |
Exact compatibility should be confirmed against the probe model, Proximitor sensor model, and total system length.
Quality Control Process (DYNAMIC GENERATION)
- Part-number verification: Confirm 330130-045-01-00 on the cable label or packaging.
- Visual inspection: Check the armored cable jacket for cuts, crushing, corrosion, or insulation degradation.
- Connector inspection: Inspect both ClickLoc connectors for bent pins, corrosion, seal damage, or loose locking rings.
- Continuity test: Verify cable continuity and insulation resistance if test equipment is available.
- System length check: Confirm the total system length (probe + extension cable) matches the Proximitor sensor configuration.
- Label and approval check: Verify the 00 approval marking (no agency approval) matches the site certification requirements.
Replacement Pitfall Guide (DYNAMIC GENERATION)
❗ Do not confuse 330130 with a probe or Proximitor sensor. The 330130 is an extension cable only. It cannot replace a 330105/330106 probe or a 330180 Proximitor sensor.
❗ Match the total system length. The 3300 XL system requires a consistent total length (probe + extension cable). Mixing incompatible lengths may reduce linearity or cause measurement errors.
❗ Verify the armor option. The 01 option means armored. Replacing it with a non-armored cable (00) may reduce mechanical protection in harsh environments. Conversely, substituting an armored cable where a non-armored one was specified may affect routing flexibility and bend radius.
❗ Confirm the approval suffix. The 00 approval option means no agency approval. Substituting 05 (multi-license) or CN may be required for hazardous-area or regional compliance. Ensure the replacement meets site certification requirements.
❗ Check connector compatibility. The cable must use ClickLoc connectors compatible with the connected probe and Proximitor sensor. Damaged or mismatched connectors can cause signal instability.
❗ Do not use as a standalone signal cable. The extension cable is part of an eddy-current transducer system and must be used with a matching 3300 XL 8 mm probe and Proximitor sensor.
Compatibility Matrix & Benchmarks
| Original Model | Replacement / Alternative | Compatibility Level | Migration Notes |
|---|---|---|---|
| Bently Nevada 330130-045-01-00 | Same 330130-045-01-00 | Direct | Match full order code, length, armor, and approval. |
| Bently Nevada 330130-045-00-00 | 330130-045-01-00 | Needs Verification | Different armor option (non-armored vs. armored); verify mechanical protection needs. |
| Bently Nevada 330130-045-01-05 | 330130-045-01-00 | Needs Verification | Different approval option (05 multi-license vs. 00 no approval); confirm site certification needs. |
| Bently Nevada 330130-045-01-CN | 330130-045-01-00 | Needs Verification | Different approval option (CN vs. 00); verify regional compliance requirements. |
| Bently Nevada 330130-040-01-00 | 330130-045-01-00 | Needs Verification | Different cable length (4.0 m vs. 4.5 m); verify total system length compatibility. |
| Bently Nevada 330106-05-30-10-02-05 | 330130-045-01-00 | Not direct | 330106 is a probe; 330130 is an extension cable. |
Benchmarks:
- 3300 XL 8 mm armored extension cable for shaft vibration and displacement systems.
- 4.5 m armored cable with ClickLoc connectors.
- Standard temperature rating.
- No agency approval (option 00).
- Must be used with a matching 3300 XL 8 mm proximity probe and Proximitor sensor.
- Third-party listings that describe 330130 as a probe, transmitter, or 4–20 mA sensor are incorrect.
