Product Core Brief
- Model: 330103-00-12-10-02-00
- Brand: Bently Nevada
- Series: 3300 XL 8 mm Proximity Transducer System
- Core Function: 8 mm eddy-current proximity probe for shaft relative vibration, axial displacement, position, and Keyphasor reference when paired with a compatible 3300 XL extension cable and proximitor.
- Product Type: 3300 XL 8 mm Proximity Probe
- Key Specs: M10×1 thread | armored cable | ClickLoc connector | standard cable | no agency approval
- Condition: New Original / New Surplus
Product Introduction
Wrong probe length or cable construction is one of the most common reasons vibration channels stay offline after a turnaround. The Bently Nevada 330103-00-12-10-02-00 is the 3300 XL 8 mm proximity probe variant with an armored cable, ClickLoc connector, standard cable construction, and no agency approval. The armored cable adds mechanical protection against abrasion, crushing, and accidental damage in congested turbine or compressor bays.
This probe delivers a 2 mm linear range at approximately 7.87 V/mm (200 mV/mil) sensitivity when paired with a compatible 3300 XL proximitor such as the 330180 series. That makes it suitable for radial vibration, axial displacement, and Keyphasor applications on API 670-style monitoring channels. For this specific -00-12-10-02-00 configuration, the total cable length should be verified from the physical label before installation, since the “00” position can vary by ordering convention.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | Bently Nevada |
| Part Number | 330103-00-12-10-02-00 |
| Product Family | 3300 XL 8 mm Proximity Transducer System |
| Probe Type | 8 mm eddy-current proximity probe |
| Thread | M10×1 metric |
| Armor | Armored |
| Total Cable Length | To be confirmed from label (code 00) |
| Connector | ClickLoc, standard cable (code 02) |
| Agency Approval | None (code 00) |
| Linear Range | 2 mm (80 mils) typical |
| Sensitivity | 7.87 V/mm (200 mV/mil) typical with 3300 XL proximitor |
| System Power | −17.5 to −26 Vdc via proximitor |
| Frequency Response | 0 to 10 kHz typical (system-dependent) |
| Compatible Proximitor | 330180 series (verify model and calibration) |
| Compatible Monitor | 3500/40M, 3500/42M, 3500/44M, 3500/25, 1900/65A, etc. |
Key Selling Points & Differentiators
- Armored cable construction. Better suited than non-armored variants for mechanically exposed routing, cable trays, and areas where accidental impact is likely.
- Exact code match. This is the M10×1, armored, ClickLoc, standard-cable, no-agency-approval variant—no guessing on thread or armor.
- Drop-in 3300 XL compatibility. Works with standard 3300 XL extension cables and 330180-series proximitors without matched-component calibration.
- Proven measurement chain. 8 mm tip diameter, 2 mm linear range, and 200 mV/mil sensitivity make it suitable for radial vibration, axial displacement, and Keyphasor channels.
- Clear boundary. Not recommended for installations that require ATEX/IECEx or cNRTLus certification—this unit carries no agency approval. Also not suitable for high-temperature connector zones unless the ETR/FluidLoc variant is specified.
Quality Transparency SOP
- Part number verification. We confirm the label reads 330103-00-12-10-02-00 and matches the 3300 XL 8 mm probe family.
- Armored cable inspection. The stainless armor, outer jacket, ClickLoc connector, and probe tip are checked for crushing, corrosion, or connector pin damage.
- Continuity and insulation check. Using a Fluke multimeter, we verify center conductor continuity and shield integrity from probe end to connector.
- Tip and thread inspection. The PPS tip face and M10×1 threads are inspected for scoring, deformation, or chemical damage.
- ESD-safe packing. The probe is coiled to the recommended bend radius, sealed in an anti-static bag, and foam-packed to prevent connector stress.
Technical Risk Avoidance
❗ Confirm total cable length before installation. The “00” length code must be verified from the physical label. If the original probe was 1.0 m, 5.0 m, or 9.0 m, this unit must match exactly to avoid field rework.
❗ Do not substitute armored for non-armored without checking routing. Armored probes are heavier and less flexible. In tight bends or rotating assemblies, verify bend radius and mechanical clearance.
❗ Verify proximitor compatibility. The probe must be paired with a 3300 XL proximitor calibrated for AISI 4140 steel and the correct system length. Mismatched proximitor models can shift sensitivity and gap-voltage settings.
❗ Set gap voltage correctly. Typical mid-range gap voltage is around −10.0 Vdc, but the exact target depends on the proximitor and monitoring channel configuration. Always verify against the installed monitor setup.
Buyer’s FAQ
Is this a complete sensor system? No. This is the 8 mm probe only. A complete measurement channel also requires a compatible 3300 XL extension cable and 3300 XL proximitor.
Can I replace a 330103-00-05-10-02-00 with this? Not without checking length and armor. The -00-12-10-02-00 is an armored variant with an unconfirmed length, while -00-05-10-02-00 is a 1.0 m non-armored probe. Electrically they are similar, but mechanically they are not interchangeable.
Does this include the extension cable and proximitor? No. Unless explicitly stated, this listing covers the probe only. Extension cable and proximitor are separate line items.
Is this genuine Bently Nevada? Yes. We sell genuine surplus inventory. The part number is verified against the physical label before dispatch. No clones or rebuilt substitutions.
What warranty applies? Standard 12-month warranty against DOA and functional defects. Mechanical damage from incorrect installation, gap setting, chemical exposure, or cable crushing is not covered.
