Product Core Brief
- Model: 330103-00-06-10-02-CN
- Brand: Bently Nevada
- Series: 3300 XL 8 mm Proximity Transducer System
- Core Function: 8 mm eddy-current proximity probe for shaft relative vibration, axial displacement, position, and Keyphasor reference when paired with a compatible 3300 XL extension cable and proximitor.
- Product Type: 3300 XL 8 mm Proximity Probe
- Key Specs: M10×1 thread | non-armored | 1.0 m total cable | ClickLoc connector | standard cable | multi-license approval
- Condition: New Original / New Surplus
Product Introduction
Turnaround schedules slip when the wrong probe arrives on site. The Bently Nevada 330103-00-06-10-02-CN is the 3300 XL 8 mm proximity probe variant built for M10×1 metric mounting, with a 1.0 m integrated cable, ClickLoc connector, standard cable construction, and multi-license agency approval.
This probe delivers a 2 mm linear range at approximately 7.87 V/mm (200 mV/mil) sensitivity when used with a compatible 3300 XL proximitor such as the 330180 series. The “CN” approval code means this unit carries multi-license certifications, which is important for installations requiring ATEX/IECEx or cNRTLus compliance—though the exact approval drawing and installation constraints must be confirmed from the physical label before commissioning. For this specific -00-06-10-02-CN configuration, the unthreaded length and overall case length should be verified against the label, since the “00” position can vary by ordering convention.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | Bently Nevada |
| Part Number | 330103-00-06-10-02-CN |
| Product Family | 3300 XL 8 mm Proximity Transducer System |
| Probe Type | 8 mm eddy-current proximity probe |
| Thread | M10×1 metric |
| Armor | Non-armored |
| Total Cable Length | 1.0 m (code 06) |
| Connector | ClickLoc, standard cable (code 02) |
| Agency Approval | CN – Multi-License Approval |
| Linear Range | 2 mm (80 mils) typical |
| Sensitivity | 7.87 V/mm (200 mV/mil) typical with 3300 XL proximitor |
| System Power | −17.5 to −26 Vdc via proximitor |
| Frequency Response | 0 to 10 kHz typical (system-dependent) |
| Compatible Proximitor | 330180 series (verify model and calibration) |
| Compatible Monitor | 3500/40M, 3500/42M, 3500/44M, 3500/25, 1900/65A, etc. |
Key Selling Points & Differentiators
- Exact code match. This is the M10×1, non-armored, 1.0 m, ClickLoc, standard-cable, multi-license approval variant—no guessing on thread, length, or certification.
- Drop-in 3300 XL compatibility. Works with standard 3300 XL extension cables and 330180-series proximitors without matched-component calibration.
- Multi-license approval. The “CN” suffix indicates multi-license certifications, useful for sites requiring ATEX/IECEx or cNRTLus compliance—always confirm the installed approval drawing.
- Clean field termination. ClickLoc connector reduces installation time compared with bare-wire or compression-fitting probes.
- Clear boundary. Not recommended for high-temperature zones above 177°C at the probe lead or for oil-immersed connector locations unless FluidLoc or ETR variants are specified. This unit is standard cable, non-armored.
Quality Transparency SOP
- Part number verification. We confirm the label reads 330103-00-06-10-02-CN and matches the 3300 XL 8 mm probe family.
- Cable and connector inspection. The 1.0 m cable jacket, ClickLoc connector, and probe tip are checked for cracks, corrosion, or pin damage.
- Continuity and insulation check. Using a Fluke multimeter, we verify center conductor continuity and shield integrity from probe end to connector.
- Tip and thread inspection. The PPS tip face and M10×1 threads are inspected for scoring, deformation, or chemical damage.
- ESD-safe packing. The probe is coiled to the recommended bend radius, sealed in an anti-static bag, and foam-packed to prevent connector stress.
Technical Risk Avoidance
❗ Confirm total length before installation. Code “06” indicates 1.0 m total length. If the original probe was 5.0 m or 9.0 m, this unit will not reach the extension cable or proximitor without rework.
❗ Do not mix cable types blindly. This is a standard-cable ClickLoc variant (code 02). It should not be substituted for FluidLoc (code 1x) or armored (330104) variants in wet or mechanically exposed locations.
❗ Verify proximitor compatibility. The probe must be paired with a 3300 XL proximitor calibrated for AISI 4140 steel and the correct system length. Mismatched proximitor models can shift sensitivity and gap-voltage settings.
❗ Confirm the approval drawing for hazardous areas. The “CN” code means multi-license approval, but the exact installation requirements—such as IP rating, terminal protection, and voltage limits—must be verified against the physical label and applicable drawing before commissioning in Zone 2 / Division 2 areas.
Buyer’s FAQ
Is this a complete sensor system? No. This is the 8 mm probe only. A complete measurement channel also requires a compatible 3300 XL extension cable and 3300 XL proximitor.
Can I replace a 330103-00-06-10-02-00 with this? Electrically and mechanically they are very similar. The key difference is the approval code: “CN” means multi-license approval, while “00” means no agency approval. If your installation does not require certified approval, either variant may work—but confirm the label before substitution.
Does this include the extension cable and proximitor? No. Unless explicitly stated, this listing covers the probe only. Extension cable and proximitor are separate line items.
Is this genuine Bently Nevada? Yes. We sell genuine surplus inventory. The part number is verified against the physical label before dispatch. No clones or rebuilt substitutions.
What warranty applies? Standard 12-month warranty against DOA and functional defects. Mechanical damage from incorrect installation, gap setting, or chemical exposure is not covered.
