Product Core Brief

• Brand: GE Fanuc / Emerson Automation
• Model: IC695PSD040F
• Series: PACSystems RX3i
• Core Function: 40W basic DC rack power supply providing regulated multi-rail logic power to RX3i universal backplane; designed for standalone, non-redundant control racks with low to moderate module loading
• Type: Single-slot rack-mounted backplane power supply
• Condition: New Original (New Surplus)
• Status: ⚠️ Discontinued OEM production; limited surplus inventory
• Key Spec Highlights: 18–30VDC startup input, 12–30VDC operating range, total 40W maximum output, no load-sharing / parallel redundancy capability, front diagnostic LEDs, protected output on/off switch

Key Technical Specifications

• Nominal Input: 24 VDC Startup range: 18–30 VDC Continuous operating range: 12–30 VDC
• Maximum Input Power: 60 W
• Total Rated Output Power: 40 W maximum
• Backplane Output Rails · +5.1 VDC · +3.3 VDC
• Front Panel Indicators: POWER, P/S FAULT, OVER TEMP, OVERLOAD LEDs
• Front Control: Protected on/off switch (controls module outputs only, input power remains live)
• Protections: Overload, overvoltage, short-circuit, reverse input polarity protection
• Redundancy Support: Does NOT support parallel load sharing or N+1 redundant operation
• Hot Swap: Not recommended; power should be disconnected before removal to avoid arcing
• Hold-up Time: 10 ms minimum at minimum rated input
• Inrush Current: 4 A maximum for 100 ms
• Wiring Terminals: Accepts 14 AWG – 18 AWG copper conductors
• Operating Temperature: 0 °C to +60 °C (thermal derating required above 50°C)
• Storage Temperature: −40 °C to +85 °C
• Humidity: 5%–95% non‑condensing
• Mechanical: Occupies one slot on RX3i universal backplane, typically installed in Slot 0
• Certifications: UL, CE

Product Introduction

Small-scale manufacturing, remote auxiliary and water treatment control racks with limited I/O density often utilize basic non-redundant power architecture. GE delivers stable regulated logic power for lightly populated RX3i chassis.

This unit offers comprehensive fault monitoring to alert maintenance teams of overload and over-temperature conditions before unplanned system resets. It is intended strictly for standalone single-power-supply installations. Its single-slot footprint enables direct drop-in replacement within existing non-redundant RX3i racks during planned maintenance windows.

Key Selling Points & Differentiators

1. GE is a cost-effective 40W power supply optimized for lightly loaded RX3i racks without redundant power requirements.
2. Four dedicated front-panel diagnostic LEDs enable fast visual troubleshooting of power, overload and thermal faults.
3. Every unit undergoes full bench validation on an RX3i test chassis; load sweep, LED operation and protection circuit triggering verified prior to shipment. Signed test documentation available on formal request. Warranty runs 12 months post delivery.
4. Wide DC input operating range tolerates voltage fluctuation common in remote cabinet installations.
5. Not recommended for RX7i, Series 90‑70 or Series 90‑30 racks. Designed exclusively for RX3i universal backplane architecture.
6. Compact single-slot form factor preserves rack space for I/O and communications modules in space-limited enclosures.

Quality Transparency SOP

• Incoming Verification: Serial traceability validation, anti-counterfeit visual inspection, terminal block and switch cover hardware cross-check.
• Live Bench Test: Dedicated RX3i test rack, power-on self-test, variable load simulation, fault condition verification, continuous 24-hour thermal soak cycling.
• Electrical Tests: Input voltage range sweep, overload shutdown testing, chassis ground continuity verification.
• Hardware Verification: Confirm LED array and output switch operate per datasheet; no unauthorized component rework performed.
• Final QC & Packaging: Anti-static shielding, shock-dampened transit carton, signed QC Pass label. Test images and logs available on request. No zero-failure performance guarantee.

Technical Risk Avoidance Section

Redundancy Misconfiguration Risk Risk: Attempting to parallel multiple modules for redundant power results in unstable backplane voltage and potential module damage. Prevention: Select IC695PSD140E for all N+1 redundant rack designs. Field note: Multiple remote pumping stations experienced intermittent CPU resets after technicians wired two PSD040F units in parallel for backup power.

Thermal Derating Risk Risk: Sustained cabinet temperature above 50°C requires reduced rack power draw; full 40W rating cannot be maintained. Prevention: Calculate total chassis power consumption and apply thermal derating rules for high-temperature enclosures.

Hot Swap Risk Risk: Removing or inserting the module with input power energized creates electrical arcing and may damage backplane contacts. Prevention: Isolate upstream 24VDC supply before module replacement.

Power Budget Miscalculation Risk Risk: Overpopulating the rack with high-current CPU, communications and analog I/O exceeds the 40W total capacity. Prevention: Sum backplane power draw of all installed modules and maintain minimum 15% power headroom.

Critical Summary: Confirm redundancy requirements before procurement. This module cannot be paralleled for load sharing; it is not electrically interchangeable with IC695PSD140E without redesigning cabinet power architecture. It operates exclusively within RX3i racks.

FAQ

1. Q: Can GE be installed into RX7i or Series 90‑70 racks? A: No. It is built exclusively for RX3i universal backplanes; mechanical and electrical interfaces are incompatible with other GE PLC families.
2. Q: Can multiple modules be connected in parallel for redundant power? A: No. This model lacks internal load-sharing circuitry. Use IC695PSD140E if redundant power is required.
3. Q: Does this module support hot-swap replacement while the RX3i rack remains energized? A: Not supported. Disconnect upstream 24VDC input power before removing or installing the module to prevent arcing.
4. Q: What lead times apply for available inventory? A: In-stock units ship within 1–3 business days. Backordered allocations require 5–7 week lead times subject to global surplus availability.
5. Q: What failure modes fall outside warranty coverage? A: The 12-month limited warranty covers manufacturing defects. Damage from parallel redundant wiring attempts, sustained overload, ESD, and operation outside published temperature range is excluded.
6. Q: What is the core difference between and IC695PSD140E? A:

• : 40W, standalone only, no load sharing / redundancy capability
• IC695PSD140E: 40W, supports parallel load sharing and N+1 redundant configurations They share physical slot form factor but cannot directly substitute without power system redesign.

1. Q: Does the front panel on/off switch disconnect the incoming 24VDC supply? A: No. The switch only disables the module’s output rails; input power remains live to internal circuitry.