Product Core Brief
- Model: PM864K01
- ABB Part No.: 3BSE018150R1
- Brand: ABB
- Series: S800 I/O / AC 800M controller family (800xA platform)
- Core Function: Controller CPU module — executes the application program, manages S800 I/O modules over the backplane, and maintains communication with the 800xA system
- Product Type: Process control CPU module / legacy automation spare
- Condition: New Original / New Surplus
Key Technical Specifications
| Category | Parameter | Value |
|---|---|---|
| Identification | Module Designation | |
| Identification | ABB Part Number | 3BSE018150R1 |
| Identification | Revision | VERIFY — confirm from nameplate |
| Platform | System | AC 800M / 800xA, S800 I/O |
| Function | Module Type | Controller CPU |
| Redundancy | Capability | VERIFY — commonly quoted as redundant-capable; confirm from ABB manual |
| Interfaces | Backplane | S800 I/O backplane (VERIFY slot position) |
| Interfaces | Communication | VERIFY — confirm supported fieldbus / Ethernet ports |
| Electrical | Supply Voltage | VERIFY — S800 system supply |
| Environmental | Operating Temperature | VERIFY — reseller figures conflict |
| Software | Configuration | ABB 800xA / AC 800M engineering tools |
| Compatibility | Interchangeable Variants | VERIFY — do not assume from “PM86” prefix |
| Supply | Availability Status | Legacy / obsolete stock |
Product Introduction (No Fluff)
ABB PM864K01 (part number 3BSE018150R1) is a controller CPU for the AC 800M / 800xA S800 platform — the module that runs the application, drives the S800 I/O, and keeps the controller connected to the wider 800xA system. On a live plant, it is the part whose failure stops a control block, which is why it is held as a spare rather than sourced under pressure.
Two details decide whether a replacement works. First, the revision — “PM864K01” is the designation, but the revision printed on the nameplate determines whether the existing application boots cleanly. Second, the series boundary: PM864 and PM865 are distinct CPUs in the same family, and a mismatched model or revision can reject the loaded application or break a redundant pair. Bottom line: confirm the complete nameplate string, not just the prefix.
QA & Testing SOP
- Anti-counterfeit intake. Nameplate photographed under raking light; designation, part number, revision, and lot code checked for consistent laser depth. Counterfeits fail on the trailing characters.
- Connector and board inspection. Backplane connector and pins checked for bending, oxidation, and heat discoloration. A single damaged pin on a CPU mimics a field fault.
- Rack power-up. Installed in a known-good S800 test rack. Startup sequence and front-panel LED states compared against the ABB manual’s expected pattern.
- Function verification. Application loaded through the 800xA engineering tools; I/O channels polled and confirmed to respond; redundant switchover exercised where a test rig exists.
- ESD-safe, moisture-protected packing. Anti-static bag, foam cradle, humidity indicator, sealed and photographed before dispatch.
Installation Pitfalls & Guide
❗ Model confusion. Confirm PM864K01 specifically — do not substitute a PM865 or other sibling on the assumption of interchangeability.
❗ Revision mismatch. Confirm the revision before ordering. A physically compatible CPU with the wrong revision may reject the loaded application.
❗ Application is not stored on the module. A replacement boots with defaults. Restore the 800xA application and configuration before energizing.
❗ Redundancy state. If your system runs a redundant CPU pair, identify the primary before removal to avoid an unplanned switchover during operation.
❗ Slot discipline. S800 modules are position-sensitive. Confirm the slot against the hardware configuration before insertion.
Replacement sequence:
- Pre-install — photograph slot position, cabling, and LED states; export the application.
- Removal — follow the documented procedure; label every cable.
- Install — seat fully, restore grounding, torque to spec.
- Commissioning — cold boot, load application, validate each I/O channel against a known reference, confirm healthy status on both legs, then return the block to service.
Technical FAQ
Is pricing negotiable on volume? On legacy 800xA stock, price follows availability rather than quantity. Tell us your real requirement up front.
What warranty applies? Twelve months on New Original. Six months on New Surplus. We state the difference rather than bury it.
Is PM864K01 the same as 3BSE018150R1? Yes — the designation and the ABB part number refer to the same module. Order using either, but confirm both appear on the nameplate.
Will any PM86-series module swap into my rack? No. Model suffixes and revisions differ, and the application must match. Confirm the complete part number and revision.
Why not upgrade to a current ABB control platform? Because a newer platform changes I/O architecture, network topology, and commissioning — that’s an engineering project, not a purchase order. If you want that path, we’ll scope it honestly.
