IS220PAICH1A
IS220PAICH1A
IS220PAICH1A
IS220PAICH1A
IS220PAICH1A

GE IS220PSVOH1B | PSVO Dual Servo Control I/O Pack for Mark VIe – Field Service Notes

  • Model: IS220PSVOH1B
  • Alt. P/N: 336A5026ADP18
  • Product Series: GE Speedtronic Mark VIe / VIeS
  • Hardware Type: PSVO Servo Control I/O Pack
  • Key Feature: Dual independent WSVO servo loops, auto-reconfigurable, enhanced fault diagnostics
  • Primary Field Use: Interfaces IONet to TSVO terminal boards; closed-loop control of turbine servo valves
Get a Quote
In Stock
Manufacturer:

Our extensive catalogue, including , is available now for dispatch to the worldwide. Brand:
The listed price is not final; the actual selling price is negotiable based on current market conditions.

Description

Hard-Numbers: Technical Specifications

  • Network: Dual 100Mbps full-duplex IONet Ethernet (ENet1/ENet2)
  • Servo Loops: 2× independent WSVO channels
  • Output Signal: ±10V DC (servo coil drive)
  • Feedback Inputs: 8× LVDT/RVDT, 2× pulse rate (2–14kHz)
  • Isolation Rating: 2000V DC field-to-backplane
  • Power Requirements: 24 VDC (22.5–28.6V), 9.0W max
  • Operating Temp: -30°C to +70°C
  • Memory: 16MB SDRAM, 32MB Flash
  • Dimensions: 263 × 58 × 28 mm
  • Weight: ~0.96 kg
  • Cooling: Convection (no fans)
  • Certifications: Class I Div 2, Zone 2 hazardous locations
  • Indicators: ENet1/ENet2, PWR, ATTN, ENA1/2 LEDs
IS220PAICH1A

IS220PAICH1A

The Real-World Problem It Solves

Turbine fuel/steam valve control demands sub-10ms loop closure. Generic I/O introduces latency, drift, and unfiltered LVDT noise causing unstable speed/load regulation.Where you’ll typically find it:

  • Gas turbine gas/liquid fuel servo valves
  • Steam turbine inlet/extraction steam valve positioning
  • Combined-cycle turbine bypass & control valve servos

Bottom line: delivers deterministic, isolated servo control with auto-reconfiguration for minimal downtime.

 

Hardware Architecture & Under-the-Hood Logic

is a smart I/O pack with dedicated servo DSP. It handles local loop closure, reducing controller load and improving response time.

  1. LVDT/RVDT signals route to isolated input conditioning circuits.
  2. On-board DSP computes position error and generates ±10V drive outputs.
  3. Dual IONet ports exchange setpoints/status with Mark VIe controller.
  4. Internal temp sensor monitors thermal health; fault logs stored in Flash.
  5. Watchdog disables outputs on comms loss; ENA1/2 enable per-channel.
  6. Auto-reconfigure via ToolboxST Component Editor on replacement.
  7. Conformal coating resists corrosion in turbine hall environments.
IS220PAICH1A

IS220PAICH1A

Field Service Pitfalls: What Rookies Get Wrong

LVDT Phase ReversalSwapping primary/secondary wires causes positive feedback. Valve slams full open; ATTN LED flashes red.

  • Field Rule: Verify LVDT phase with signal generator pre-power-up. Document wire colors.

Poor Servo Cable ShieldingUnshielded cables pick up generator EMI. Output chatters; position oscillates >1% full scale.

  • Quick Fix: Use twisted-pair, foil-shielded cable. Ground shield at PSVO only (single-point ground).

Over-Torquing TSVO TerminalsRookies over-torque terminal screws. Cracked blocks; intermittent open circuits in LVDT loops.

  • Field Rule: Torque to 0.5 N·m (4.4 lb·in). Replace cracked blocks immediately.

Incorrect IONet IP AssignmentDuplicate IP or mismatched subnet causes comms dropouts. ENet LEDs flash red; no control.

  • Field Rule: Use ToolboxST to auto-assign IP. Verify subnet matches controller before enabling.

 

Commercial Availability & Pricing Note

Please note: The listed price is for reference only and is not binding. Final pricing and terms are subject to negotiation based on current market conditions and availability.

Related products