Description
Section 3. Product Introduction
The GE IC693CHS393 is a 5-slot remote baseplate for Series 90-30 PLC systems. It provides electrical connectivity for I/O and power modules without CPU slot, connecting to main rack via expansion cable.
This unit differs from CPU baseplates by lacking Slot 1 for CPU—only I/O modules permitted. Rated for 0–60°C operating range with IP20 protection. Supports cable runs up to 700 ft to main CPU rack—verify with OEM datasheet.
Section 4. Key Technical Specifications
| Parameter | Value |
|---|---|
| Module Type | Remote I/O Base |
| Baseplate Option | Remote (no CPU slot) |
| Number of Slots | 5 (0 CPU + 5 I/O) |
| Power Supply Slot | 1 (leftmost, unnumbered) |
| Connector | 25-Pin Female (right side) |
| Internal Power Used | 420 mA @ 5 VDC |
| Dimensions | 17.44 x 5.12 x 5.59 in. (W x H x D) |
| Weight | 2.03–2.06 lbs (0.92–0.94 kg) |
| Mounting | Panel mount (vertical/horizontal) |
| Default Rack Address | Rack 1–7 (software configurable) |
| Expansion Support | Daisy-chain from main CPU rack |
| Protection Rating | IP20 (open enclosure, dust-sensitive) |
GE IC693CHS392
Section 5. Quality Control Process
1. Incoming VerificationTrace source documentation and cross-check serial numbers against OEM records. Visual inspection for corrosion, impact damage, or connector wear. Reject units with visible PCB delamination.
2. Live Functional TestPower-on with verified power supply module in left slot. Verify I/O module detection via main CPU rack RS-232 handshake. Run continuous load simulation >24 hours while logging internal temperature—thermocouple on backplane near Slot 3.
3. Electrical Parameter TestMeasure insulation resistance with 500 V Megger; must exceed 10 MΩ. Check ground continuity from mounting tabs to backplane ground plane. Verify 5 VDC rail tolerance ±5% under full load.
4. Firmware VerificationNo firmware on baseplate itself—but photograph DIP switch positions and document revision codes. Label rack address configuration clearly.
5. Final QC & PackagingSeal in anti-static bag with desiccant pack. Apply QC Passed label with date and technician initials. Double-box with foam inserts for shipment.
Section 6. Replacement Pitfall Guide
❗ Rack Address ConflictsThe GE IC693CHS393 requires unique rack addressing in multi-rack systems. Default addresses often clash with existing configurations. Verify your current rack numbering before installation—duplicates cause bus contention errors.
❗ Cable Length LimitsRemote baseplates support cable runs up to 700 ft, but signal degradation occurs near maximum distance. Use shielded cable with proper termination at both ends. Measure your actual run length—underestimation causes intermittent I/O faults.
❗ Power Supply OversizingRemote racks lack local CPU monitoring—power must support all I/O modules independently. Calculate total current draw at 5 VDC, then add 30% headroom for margin. Undersized supplies cause voltage drop during high-load states.
❗ DIP Switch MisconfigurationFactory DIP switch settings rarely match your system requirements. Document original settings before changing. Verify rack address and termination resistor settings—wrong configuration prevents proper communication.
❗ Ground Loop IssuesLong cable runs create ground potential differences between racks. Verify common ground reference at main rack termination point. Floating grounds on remote baseplates cause noise and random I/O failures.
Keep these in mind and you’ll cut 90% of rework time.
GE IC693CHS392
Section 7. Compatibility Matrix & Benchmarks
Compatibility Matrix
- IC693CHS393 → IC693CHS391 (10-slot CPU) : Incompatible — Different form factor and slot type
- IC693CHS393 → IC693CHS392 (5-slot CPU) : Incompatible — Lacks CPU slot required for main rack
- IC693CHS393 → IC693CHS393C/E : Direct — Same form factor, verify revision code
- IC693CHS393 → IC693CHS394 (10-slot remote) : Needs Adaptation — Same remote type, different slot count
- IC693CHS393 → IC693CPU331/340/350 : Not Direct — Requires main CPU baseplate for connection
Benchmarks
- Scan cycle: 2–8 ms (simulated load, 32 I/O points, main CPU 350)
- Comms throughput: 115.2 kbps (RS-232 serial, Protocol: SNP)
- Cable length: Up to 700 ft (shielded, properly terminated)
- Backplane bus speed: 8 MHz (Series 90-30 standard)
- I/O response time: 1–2 ms (remote rack to CPU, 100 ft cable)
