Description
Product Core Brief
- Model: S-113H 3BHB018008R0003
- Brand: ABB
- Series: PCS6000 / ACS6000 converter stack components
- Core Function: Gate/interface board that manages gate control, protection interlocks, and diagnostics for medium-voltage power semiconductor stacks.
- Product Type: Converter stack gate driver/interface board
- Key Specs: Fiber-optic gate commands | Digital interlocks/feedback | Optical link to stack controller
- Condition: New Original (New Surplus)
Product Introduction
A faulty gate/interface board inside a PCS6000 or ACS6000 converter stack can lock out an entire phase leg until the correct spare is verified and seated. The ABB S-113H 3BHB018008R0003 is a board-level gate/interface unit used inside ABB medium-voltage converter stacks to translate control commands into gate signals while monitoring interlocks and local faults.
This board matters because medium-voltage drive downtime is expensive. Replacing it with the correct OEM part number avoids retrofitting, pinout guessing, or firmware mismatch. In field service, a verified S-113H 3BHB018008R0003 can restore a downed stack faster than re-engineering a substitute—especially when optical links, interlocks, and protection logic must match the original design.
Key Technical Specifications
- Part Number: 3BHB018008R0003
- Product Designation: S-113H
- Application: PCS6000 / ACS6000 power converter stacks
- Function: Gate driver and interface board for IGCT/IGBT stacks
- Control Supply: Supplied by the host drive’s auxiliary LV supply; typically 24 VDC
- Gate Command Interface: Fiber-optic links
- I/O: Digital interlocks, feedback signals, local status LEDs
- Communication: Optical link to stack controller/control backplane
- Installation: Direct-mount on inverter/heatsink assembly using standoffs; plug-in power and fiber connectors
- Operating Temperature: 0…+55 °C typical cabinet conditions
- Condition: New Original (New Surplus) / Factory Sealed
Key Selling Points & Differentiators
- Exact OEM replacement: Matches ABB PCS6000/ACS6000 stack hardware without rewiring or adapter work.
- Critical protection role: Handles gate control, interlocks, and diagnostics for medium-voltage power semiconductors.
- Fiber-optic interface: Supports reliable gate-command transmission and noise-resistant stack communication.
- Inventory-ready spare: Suitable for planned spares, emergency replacement, or scheduled maintenance outages.
- Verified condition: Shipped factory-sealed with visual QA and ESD-safe handling.
- Not recommended for low-voltage micro drives, general-purpose PLC racks, or non-ABB converter platforms.
Quality Transparency SOP
- Visual inspection: Check PCB, connectors, optical ports, and labeling for damage, corrosion, or handling marks.
- ESD-safe handling: Packed in anti-static shielding with sealed protection for optical interfaces.
- Connector verification: Inspect fiber-optic ports, backplane connectors, and screw-mount points for wear or bent pins.
- Control supply check: Verify auxiliary LV supply compatibility with the target converter cabinet documentation.
- Functional validation: When test infrastructure is available, verify optical link continuity, LED status response, and interlock feedback before shipment.
Technical Risk Avoidance
❗ Confirm cabinet compatibility first. This board is intended for PCS6000/ACS6000 converter stacks. Do not install it in unrelated drive families without written confirmation from ABB documentation.
❗ Handle optical links carefully. Fiber-optic connectors must be clean, undamaged, and correctly seated. Contamination or misalignment can cause gate-command faults.
❗ Verify auxiliary LV supply. The board is supplied by the host drive’s low-voltage control bus. Wrong supply voltage can damage the module or prevent commissioning.
❗ Check firmware and hardware revision. Converter stacks may depend on specific board revisions. Mismatched revisions can cause protection timeouts or commissioning failures.
Buyer’s FAQ
Is this an original ABB part?
Yes. The listing is for ABB S-113H 3BHB018008R0003 as a new original/new surplus, factory-sealed unit. We do not relabel third-party substitutes.
Can I use this board in any ABB drive?
No. It is designed for PCS6000/ACS6000 converter stack applications. Confirm your cabinet type, stack configuration, and existing part number before ordering.
What condition is the unit?
New Original (New Surplus) / Factory Sealed, unless otherwise stated in the product listing. Photos and batch details can be confirmed before dispatch.
Do you offer a warranty?
Yes. A standard warranty applies from receipt. Exact terms depend on stock batch and installation conditions. Industrial control boards must be installed by qualified personnel.
How fast can you ship?
Lead time depends on current inventory and destination. For urgent converter-stack outages, request same-day confirmation so we can prioritize packing and logistics.
