Product Core Brief
- Model: VIBRO IOC4T 200-560-000-111
- Brand: VIBRO-METER
- Series: VM600 Machinery Protection System
- Core Function: Signal interface and I/O expansion card for MPC4 mechanical protection cards.
- Product Type: Industrial Input/Output Module
- Key Specs: 4 Dynamic Inputs | 2 Tacho Inputs | 4 Relays
- Condition: New Original (New Surplus) / Factory Sealed
Product Introduction (Rotation Engine)
Signal integrity often fails at the interface, not the sensor. This VIBRO IOC4T 200-560-000-111 bridges that gap for VM600 systems. It mounts directly to the rear of the rack, handling sensor wiring and external control signals. Think of it as the physical handshake between your MPC4 processing card and the field.
Unplanned downtime costs thousands per minute. This automation unit ensures reliable signal transmission to prevent false trips. It supports hot-swapping, cutting repair time by up to 80% during critical failures. (Though your mileage may vary based on backplane load). Reliable I/O means your protection logic actually executes when it matters.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Dynamic Signal Inputs | 4 Channels (Filtered) |
| Tacho/Speed Inputs | 2 Channels |
| Relay Outputs | 4 (Software Controlled) |
| Programmable Outputs | 32 Open Collector |
| Analog Outputs | Buffered Voltage/Current |
| Operating Temp | -20°C to +70°C |
| Protection Level | IP20 |
| Installation | Rear Rack Mount / Hot-Swap |
| EMI Protection | Integrated Filtering |
| Communication | Internal Backplane Bus |
Key Selling Points & Differentiators
- Hot-Swap Capability: Replace this industrial controller without powering down the VM600 rack, maintaining continuous monitoring.
- Integrated EMI Filtering: All inputs and outputs feature hardware filtering to reject industrial noise, ensuring data accuracy.
- High-Density I/O: Packs 4 dynamic inputs, 2 tacho inputs, and 4 relays into a single card footprint, saving rack space.
- Direct Backplane Connection: Eliminates intermediate cabling between the MPC4 and field wiring, reducing failure points.
- Not Recommended For: Standalone use without a corresponding MPC4 card; this surplus component is strictly a slave interface.
Quality Transparency SOP (DYNAMIC GENERATION)
We don’t just visually inspect this OEM replacement module. Every VIBRO IOC4T 200-560-000-111 undergoes specific functional validation:
- Backplane Communication Test: Verified data handshake with MPC4 master card using diagnostic software.
- Signal Injection Test: 4-20mA and voltage signals injected into dynamic inputs; output verified at terminal block.
- Relay Actuation Cycle: All 4 relays cycled 50x under load to verify contact integrity and coil response.
- Thermal Stability Check: Module run at 60°C ambient for 2 hours while monitoring output drift.
- Anti-Static Sealing: Packaged in ESD-safe shielding with desiccant after final QA pass.
Technical Risk Avoidance (DYNAMIC GENERATION)
❗ Backplane Slot Pairing: This I/O module MUST be installed in the rear slot directly paired with its specific MPC4 card. Misalignment causes communication faults.
❗ Wiring Torque Specs: Terminal screws on this unit are small. Over-torquing strips the threads; under-torquing causes arc faults. Use a calibrated inch-pound torque driver.
❗ Grounding Loops: Shield grounds for sensor cables must be terminated at the IOC4T shield bar, NOT the cabinet ground. Floating shields here create noise that looks like vibration.
❗ Firmware Compatibility: Verify MPC4 firmware revision before installation. Older MPC4 Mk1 cards may require specific IOC4T hardware revisions to support all 32 open-collector outputs.
Buyer’s FAQ
Is this VIBRO IOC4T 200-560-000-111 a genuine OEM part?
Yes. We source directly from authorized surplus channels. No clones or re-marked generics.
What is the difference between New Surplus and Refurbished?
New Surplus is unused, original packaging, never installed. Refurbished units have been previously used, tested, and restored to spec. This listing is for New Surplus unless noted.
Will this work with my older MPC4 Mk1 card?
Generally yes, but check the suffix. The -111 suffix indicates specific relay/contact configurations. Verify against your MPC4 manual for full compatibility.
Do you offer a warranty on surplus VM600 cards?
Yes. All units carry a 1-year functional warranty. If it fails under normal use, we replace it. No restocking fees.
How fast can you ship this VIBRO IOC4T 200-560-000-111?
In-stock units ship same-day if ordered by 2 PM EST. We know machinery protection is critical; we don’t hold inventory hostage.
